Recent content by theDogger

Kool thanks for the response. Ya I get it that it all depends on your personal preferences but I remember reading some where that it should be before and modulation effects. So if I have Delay, Chorus runn it need to be before those type of effects. As per the BBE manual SET-UP...

Ok so I am building up my rack system and have a few questions about signal path and where to put things. So far I just have the following Amp: +++++++ Egnator Vengeance Pedal Board: +++++++ Boss NS-2 Ibanez Tube Screamer MXR 10-Band EQ Rack: +++++++ Furman PWR Conditioner Korg Tuner TC...

So I just purchased what is a brand new G-Major. Local producer bought it for a session and never used it. So I made him a 2x12 cab and we swapped. Its basically brand new. Its on the most recent firmware 1.27. I have downloaded the manual and read through it but this part makes no sense to...

OK one more request. I design replica cabs. I am working on the Mesa Boogie Mini Recto's. Here is the straight that I completed and have to cover now. I am trying to figure out how the front grill goes together on the slant cab with it only being a single speaker that is slanted. Would it be...

That would greatly appreciated! Plz follow up! :mrgreen:

I am looking for complete measurements of the Mini Recto Slant Cab All the site lists is 3 measurements. There should be 4 for the slant cabs? Height: 19 3/4" Width: 18" Depth : 11" Whats the top Depth? Anyone?

Does anyone know what the radius is on the guitar cab round overs on the Recto series? Is it 1/2" or 3/4"? I know the Marshall's are 3/4" to fit their plastic corners. But with the leather corners that Mesa uses its different and I don;t have one locally to check out and confirm. Building a...

Can anyone confirm what the radius on the corners in on the Recto Cabs? Is it 1/2", 3/4" or 1". I am in the process of making a replica 2X12 RECTO HORIZONTAL CABINET. Here are some pic, I have a 1/2" radius right now, I figure its easier to take it off than put it back on. I'll post more...

I know that this is an old post but just got a Dual Rec and I want to mod the FX. I also presently have a Single Rec that I modified the FX and couldn't be happier.... That was easy! The question that I have about the Dual Rec FX mod is that the 3 gray wires that are disconnected from the board...

Ok does this help??? I have the schematics if that will help...thanks for the help... theDogger

Was wondering how Mesa is powering the blue LED's in the transatlantic. Are they running it off the power switch and the power light? Is it converting down to 12v on the power light? theDogger

Well I did the mod last night is was so easy. All I had to do was heat the a soldering iron and remove the 3 wires. The one one the far left I clipped it and put some heat shrink on. The 2nd wire from the left I removed all together and the 3rd wire I soldered it back into the 2nd hole where the...

Hey I have been searching high and low but can not find a schematic for the FX Loop mod for a Solo50 Rec. Rev2. I searched this board and have found it for just about every other REC. but the Solo50 Rev.2 I have even contacted Mesa with no reply Help any one... theDogger

Ok looked around and I am not finding a clear cut answer to a few things. 1. Will I lose the SOLO boost w/ the mod? (some say "YES" some say "NO") 2. Will a patch cable have to be used if no effects are in the loop? 3. I can't find an schematics for the SOLO 50 Rev.2 Recto for the mod. Anyone...

I am researching it right now...I post back what I find...I love DIY's theDogger