Tremoverb aluminum tube shield/bar

Discussion area for Single, Dual and Trip Rectifers

Moderators: Guitarzan, Grandor, ned, Platypus

Post Reply
Ua the Destroyer
Mark I
Posts: 42
Joined: Sun Feb 26, 2012 8:11 pm

Tremoverb aluminum tube shield/bar

Post by Ua the Destroyer » Fri Apr 19, 2019 2:34 pm

Anyone able to hook me up with the dimensions on this part? I’m talking about the aluminum U-channel at the back that guards the tubes.
I know it needs to be 26” long and I recall it being around 1/8” thick but I don’t know the width or the height of the legs on the U.
Thanks in advance.

stephen sawall
Single Recto
Posts: 1355
Joined: Tue Nov 20, 2007 9:58 pm
Location: seattle wa usa

Re: Tremoverb aluminum tube shield/bar

Post by stephen sawall » Fri Apr 19, 2019 5:45 pm

Marked for later.
The fact that Stephen appears from nowhere, is sentenced to death in an emotional public trial without anyone interfering at all and is then altogether forgotten as if nothing happened, is already suspicious.

kguitars
Mark I
Posts: 40
Joined: Sat Jun 23, 2012 4:21 am

Re: Tremoverb aluminum tube shield/bar

Post by kguitars » Sun Apr 21, 2019 7:28 pm

Width----1 1/2"(1.5")
Leg height including the bar thickness of 1/8"(0.125")----1/2"(0.5")
Leg height without the bar thickness meaning just the inside height of the U----3/8"(0.375")

The dimensions taken from my stiletto head.
Stiletto Trident Stage 1 Head
Lonestar Classic 2x12 Combo
Mini Rectifier
Trans Atlantic TA-30 2x12 Combo
Rectifier Cabinet 2x12

tbonesullivan
Mark II
Posts: 109
Joined: Wed Aug 04, 2010 10:32 am
Location: New Jersey, USA

Re: Tremoverb aluminum tube shield/bar

Post by tbonesullivan » Mon Apr 22, 2019 12:08 am

You can probably get the right U-channel off of amazon.

I do NOT know why people always seem to take these off the amp, and not put them back. I needed to get one for my DC-5 as well. You can get them from Mesa usually.
Guitars: Hamers, Heritages, G&L Legacies, EBMM Steve Morse, Carvin Bolt, Fender Tele
Amps: DC-5 1x12, Maverick 2x12, Stiletto ACE 1x12, Trem-O-Verb 2x12

Ua the Destroyer
Mark I
Posts: 42
Joined: Sun Feb 26, 2012 8:11 pm

Re: Tremoverb aluminum tube shield/bar

Post by Ua the Destroyer » Mon Apr 22, 2019 3:33 am

Thanks so much. My guess would have been right.

Yeah I could get one from Mesa but they quoted me over $100 for it. For a piece of common aluminum with 2 holes in it, seems high even for MESA. Especially considering many other parts on it are quite reasonable.
I’ve had it for a dozen years but it was missing it as far as I remember when I traded for it. I know the tremoverb combo I traded it for had one.

kguitars
Mark I
Posts: 40
Joined: Sat Jun 23, 2012 4:21 am

Re: Tremoverb aluminum tube shield/bar

Post by kguitars » Mon Apr 22, 2019 4:29 am

Additional info

Bar----24" long
Screw holes----0.16" in Dia located 3/8" from the edges.
Screw Size----0.16" in Dia & 0.55" long
Stiletto Trident Stage 1 Head
Lonestar Classic 2x12 Combo
Mini Rectifier
Trans Atlantic TA-30 2x12 Combo
Rectifier Cabinet 2x12

Ua the Destroyer
Mark I
Posts: 42
Joined: Sun Feb 26, 2012 8:11 pm

Re: Tremoverb aluminum tube shield/bar

Post by Ua the Destroyer » Mon Apr 22, 2019 3:01 pm

thabks I ordered up some channel stock. The Tremoverb head must be wider because mine is for sure 26”.

Post Reply